If no change, your problem may be the harness or plug at the rear of the headlight bulb. Fold wiper blade assembly all the way back and it just slides out at angle. Take a look at the entire headlight assembly. Vince hello i am a salesman for a Toyota dealer in pa the 05 sienna has not even begun production yet and will not be on a lot until the end of September we as salesman are not yet familiar with what they could possibly do next since they completely redesigned the 04 and the are so far ahead of the compet … etion i do not see them changing much if anything The Siennas were redigned after they performed horribly in crash tests by a popular independent institute, Now they are the top rated Minivan in safety. Always carefully thread the plug by hand or using an old plug wire to prevent the possibility of cross-threading and damaging the cylinder head bore. If it has you can use a regular headlight 'restoring' kit sold at most auto part locations. The right bulb took me twice as long to replace,if you were to figure the time just to replace the bulb, as the space was far more limited than on the driver's side.
Headlights grow dimmer by up to 20% over time and eventually burn out - for this reason, we recommend changing your headlights in pairs. Behind the light there ate two locking bars that slip up and down. Open the battery box by snapping off the tabs, lift out, and move the vent to the side. Remove the bulb socket retaining ring by rotating it counterclockwise. Thanks again for your great work! Unscrew the ring holding the lamp.
I did this so I could install aftermarket h. I attempted to change the rear wiper on my 2005 Sienna and although I now understand how to go about this, I was not successful in completing it. With 3 small children at home it was bound to happen I guess, ha! Because of this, you need to replace the actual wiper blade the rubber part separate from the frame. Lots of good info for the shade tree mechanic. Everything else is the same: Pull off the red wire cover, attached retaining clip and pull the bulb out etc.
Oct 15, 2015 Remove plug from light bulb, using 12 volt test light hook up ground to negative side of battery,then touch probe on positive terminal to make sure test light is functional. Screw on the back of the assembly. Feb 04, 2013 When looking from the outside of the headlight at the bulb, can you see the bulb clearly?? Second a good long flat head screwdriver. It seems easy once you've done it. You will see a retainer spring that attaches to one side of the bulb holder. Turn the lamp retaining collar to the left and remove. For additional information, please refer to the following topic s : Engine Electrical, Ignition Coil.
The assembly will now pull out of the front of the vehicle. Gently push the circular ends in towards the front of the car and then separate them. Directly behind the hex screws there are two tabs, one behi … nd each hex screw. If resistance is felt before the plug is almost completely threaded, back the plug out and begin threading again. This method of removal should allow you access to the High-beam, as well. Remove the old bulb and install the new one being careful not to touch the glass of the new bulb with bare fingers. Pull the two black tabs with the L shaped bracket toward the back and then up and pull out Located at the back of the headlamp to release the headlamp assembly from the vehicle and pull headlamp assembly forward.
You must remove the entire plastic housing. Actually, I believe my three bolts and one screw method might be a tad easier: Low Beam. It was overall one of the best online shopping experiences. Do not touch the glass of the new bulb, the oil from your hands could cause it to burn out when you turn the light on! All trims are equipped with a 210-horsepower, 3. When you change the headlight on your Sienna, it is important to not touch the glass part of the bulb with your fingers because the oil from your fingertips will cause that part of the bulb to burn hotter, which significantly shortens the life of the bulb. Remove nut with 10mm wrench or ratchet. Once the grey cover is removed you will see two connecting wires: The grey wire at 12:00 and the red at 6:00.
Fuel Tank Capacity, Approx gal. Carefully pull bulb straight out of the socket and push in the new bulb. Gently pull the red wire off of the back of the bulb and then a small retaining clip attached. Rotate the bulb socket of the offending bulb counterclockwise and remove from the lamp assembly. Fuel Tank Capacity, Approx gal.
Half-way down the low beam bulb, there is a circular metal contact shaved at a angle on the left side as you are looking from back to front that needs to mate against the other. Loosen the bolt and remove. The only real problem is the retaining rings that hold the bulb in place usually breaks when removed. Hard to split apart and get back together without damaging. Use the screw driver to pull up the metal straps and then slide forward the entire assembly. Immediately behind the headlamp housing you should find a large 3 or 4 inch diameter, I'd guess screw off cap.
The headlight lens is held in with 1 bolt on the front inside end of the lens, and 2 retainer pins at the backside pull straight up to remove. As a proud owner of the highly rated Toyota Sienna, you know how important vehicular safety is. Next, peel the rubber fitting around the bulb located on the back of the headlamp assembly. It looks like the cross section of a tire with a double ended arrow inside it. This requires you to push the top part of the wire toward the front of the car and lift up. Make sure that you install only reliable and high-quality parts in your daily driver, like AutoZone's premium Toyota Sienna headlights. In small to reach areas, an old spark plug wire and boot or a short length of rubber hose, placed on the spark plug, could be used as a threading tool.